Piezometer Model IG 1401 & IG 1501
Specifications
Piezometer Model IG 1401 | ||
Material (outer body) (1%fs ; 0.5%fs optional) | Stainless steel | |
Operating Temperature | -10 to 70°C | |
Dimension | 20mm dia x 145 mm length | |
Cable | 1m , 4 core shielded. | |
Coil Resistance Thermistor |
140 – 160 Ohm @ 25°C YSI 44005 or equivalent (3k Ohm @ 25°C) |
Standard Ranges
Innovative series IG-1400/1500 piezometers are used
to measure ground water elevations and pore water
pressures in bore holes, embankments, concrete
structures, pipe- lines, wells, mines, tunnels etc. Model
IG-1501 has the filter replaced with a threaded
adapter to permit it to be coupled directly to pressure
lines. Provision of gas discharge tube protects the
sensor against surge and lightning.
3,5,7,10,20,35,50
(Higher ranges on request)
Non-linearity %fs
Surge arrestor
Filter
Citel 90V Gas Discharge tube
High and low air entry Ceramic
Typical Applications
Controlling water pressure during consolidation by continuous monitoring.
Prediction of slope failure and remediation.
Design for lateral earth pressures.
Design for uplift pressures and buoyancy.
Monitor seepage, determine phreatic line and verify models of flow.
Monitor surface water run-off.
Monitor rate and direction of flow of contaminated water.
Monitor encroachment of salt water into fresh water acquifiers.
Outstanding features
Unprecedented sensitivity, long term stability and reliability.
Isolation of the sensor assembly from the effects of total stresses acting on the body of the
piezometer.
Robust and sturdy construction.
Slim-line design.
Corrosion resistant option available for coastal applications.
Provision of thermistor for temperature measurement.
Provision of gas discharge tube for lightening and surge protection.
Suitable for remote reading, scanning and Data logging.
No effect of cable length on performance of the sensor.
Piezometer : Water level gauge Model IG 1402 with 20m integral cable and vent tube Model IG-1402 Automatic Water Level Recorder is designed for accurate, remote monitoring of ground water level in a reservoir/ borehole, coastal and inland waters, ports, wells and rivers. It can also be used for recording water level in canals, open channels, sumps and underground and overhead tanks/ sumps. It essentially consists of a vibrating wire pressure sensor provided with a vent tube of required length running parallel to the sensor cable. The vent tube and cable are routed through a protective tube to a Digital read out unit, for displaying the water level in its engineering units. A special cylindrical filter with conical tip is provided to give more surface area to the sensor. The filter is fixed on to the sensor body through a threaded connector which may easily be removed for saturation. Option of disc filter is also available.
Specifications
Piezometer Model IG 1501 | ||
Standard Ranges | 10, 20, 30, 50 m water head. Other ranges available on request. Nonlinearity %fs + 0.5 % FS | |
Standard Ranges | 10, 20, 30, 50 m water head. Other ranges available on request. Nonlinearity %fs + 0.5 % FS | |
Material (outer body) | Stainless steel | |
Operating Temperature | -10 to 70°C | |
Coil Resistance Thermistor |
140 – 160 Ohm @ 25°C YSI 44005 or equivalent (3k Ohm @ 25°C) | |
Dimension | 30mm dia x 195 mm overall length. | |
Cable | 4 core cable encapsulated in a PVC tube, open to atmosphere. Maximum length 20 meter. |
Outstanding features
Surge arrestor
Filter
Citel 90V Gas Discharge tube or equivalent.
High and low air entry Ceramic
Unprecedented sensitivity, long term stability and reliability.
Isolation of the sensor assembly from the effects of total stresses acting on the body of the piezometer.
Robust and sturdy construction.
Slim-line design.
Corrosion resistant option available for coastal applications.
Provision of thermistor for temperature measurement.
Provision of gas discharge tube for lightening and surge protection.
Suitable for remote reading, scanning and Data logging.
No effect of cable length on performance of the sensor.